VersaTube VS3406014420WS Instruction Manual Page 41
- Page / 46
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
INSTALLING YOUR GARAGE DOOR IN A VERSATUBE FRAME
Note that the Versatube frame is all steel with no overhead ceiling joist. You must deviate from the door manufacturer’s
instructions to install the garage door in the Versatube frame. The following is a list of the installation steps that will be
different from the door manufacturer’s assembly instructions:
1. It is not necessary for you to frame out your door opening with 2 x 6 lumber. Track brackets will be attached directly
to the steel door frame.
2. If you have a door with torsion springs instead of a extension springs you will need to attach a center vertical over the
door header.
3. You will fasten all brackets an channels to the Versatube frame with #12 self-drilling screws instead of the lag screws
provided with your door.
4. The garage door manufacturer’s instructions call for assembling all of the door sections one at a time and using 3”
nails bent over to hold the sections in place. With the Versatube frame you will assemble only the first or bottom door
section and use it as a guide to locate and attach the vertical tracks to the door opening.
TIP: You should have two people to install the garage door.
Step 1 Track and Flag Brackets to Vertical Track
Install mounting brackets and flag bracket to the vertical rails according to the manufacturer’s instructions.
Step 2 Assemble Door Section 1
Assemble door section #1 according to the manufacturer’s instructions including the bottom weather strip, the bottom
wheel brackets and the correct hinges. Insert 4 rollers into bottom brackets and hinges and place the first door section in
the door opening with the front of the door flush with the back of the door frame. Center the door side to side. One person
must hold the door in place or brace it up with something on both sides.
Step 3 Installing Vertical Door Tracks
Slide the left vertical door track onto the wheels. Use your level to plumb the track and fasten the bottom track bracket to
the door frame with a #12 self-drilling screw ( the same screws used to assemble your frame).
Plumb the track and attach the next higher bracket to the door frame. Continue to plumb and attach all brackets and flag
bracket to the frame with self–drilling screws. When all brackets are installed go back and install one additional screw in
each bracket. Repeat this assembly for the right door track.
DOOR OPENING FRAME (JAMB)
GARAGE DOOR CENTERED
IN OPENING
BOTTOM BRACKET
ROLLER
TRACK
TRACK BRACKET
SELF-DRILLING SCREW
PAGE 41
- FOR VERSATUBE BUILDINGS 1
- CONTRACTOR SERIES 1
- 2” X 4” FRAMES 1
- ATTENTION: 3
- FOUNDATION NOTES 5
- ANCHORING THE BASE RAILS: 6
- STEP 3: ASSEMBLING THE TRUSS 10
- WEB BRACE AND BRACE BRACKET 11
- TYPICAL TRUSS 11
- 4’ TYPICAL 13
- 4’ TYPICAL, 8 PLA 13
- CORNER AT ONE END TO 15
- ATTACH OVER SIDE DOOR 15
- TRUSS WITH SHORT EAVE 15
- #12 SELF-DRILLING SCREW 16
- #13 X 2” PAN HEAD 23
- SELF-DRILLING SCREW 23
- INSTALLING THE WALK DOOR 24
- TOP VIEW, DOOR FRAME TO POST 25
- VIEW FROM INSIDE BUILDING 25
- BUILDING 26
- INSTALLING WALK DOOR SIDE 27
- TRIM (ANGLE AND J-TRIM) 27
- 2” LONGER THAN 28
- DOOR FRAME OR 28
- OUT TO FRONT 28
- EDGES OF J-TRIM 28
- FRONT FLANGE 28
- INSTALLING WINDOW 29
- NOTE: WINDOW MUST BE 30
- INSTALLED BEFORE 30
- WINDOW TRIM 30
- STEP 2: 33
- FIRST PANEL 35
- EAVE TRIM 37
- RIDGE CAP 40
- SIDE VIEW 44
- PAGE 45 45
Related products and manuals for Garage Door Opener VersaTube VS3406014420WS
(44 pages)Philips GC028/78 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Golarki do tkanin Philips GC028/78.
Dostarczamy 1 pdf podręczników Philips GC028/78 do pobrania za darmo według typów dokumentów: Arkusz Danych
Comments to this Manuals