VersaTube VS3406014420WS Instruction Manual Page 35

  • Download
  • Add to my manuals
  • Print
  • Page
    / 46
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 34
STEP 3: INSTALLING SHEET METAL PANELS ON THE ENDS OF THE BUILDING
IMPORTANT NOTE: These installation instructions are for 5 rib panels with ribs on 9” centers. If you are installing R-Panels
with 4 ribs on 12” centers, you will start installing panels from one side of the end wall and work your way to the other side.
Start the first panel 1” outside of the building frame or with the center of the edge rib centered on the outside of the outside of
the frame. If you are installing insulation with the
R-panels apply the insulation as you did on the side walls. (4’ starter and 6’ after that)
SHEET METAL PANELS: If insulating building, see the next page insulation panel layout.
Start your first panel in the center of the building end wall if your building width is 14’,20’, 26’, 32’, 38’, 44’, or 50’ Wide.
If the building is 16’, 18’, 22’, 24, 28’, 30’, 34’, 36’, 40’, 42’, 46’, 48’, or 52’ wide, locate the first panel with the center of the
edge rib centered in the building end wall.
The first panel may be over a door opening. It is critical that the first panel be perfectly plumb. It will set the tone for all of the
panels to follow. Work from the center of the building to both ends.
Trim the panels at the corner of the building if required. NOTE: If you are installing R-Panel
you can start at one side of
the end wall and work to the other side as you did the side walls.
PAGE 35
FIRST PANEL CENTERED IN
THE BUILDING END WALL
FIRST PANEL LOCATED WITH THE
CENTER OF THE EDGE RIB CENTERED
IN THE BUILDING END WALL
FIRST PANEL FIRST PANEL
CENTER PANEL HEIGHT for 3:12 roof pitch: Each panel from the peak to the eave will drop in height 9”. The following is
a list of center panel heights for 10’, 12’, 14’, and 16’ eave height buildings. For panels over door openings, subtract the
door height.
CENTER PANEL HEIGHT
Building
Width
10' Eave 12' Eave 14' Eave 16' Eave
14' 11'-10" 13'-10" 15'-10" 17'-10"
16' 12'-1" 14'-1" 16'-1" 18'-1"
18' 12'-4" 14'-4" 16'-4" 18'-4"
20' 12'-7" 14'-7" 16'-7" 18'-7"
22' 12'-10" 14'-10" 16'-10" 18'-10"
24' 13'-1" 15'-1" 17'-1" 19'-1"
26' 13'-4" 15'-4" 17'-4" 19'-4"
28' 13'-7" 15'-7" 17'-7" 19'-7"
30' 13'-10" 15'-10" 17'-10" 19'-10"
32' 14'-1" 16'-1" 18'-1" 20'-1"
34' 14'-4" 16'-4" 18'-4" 20'-4"
36' 14'-7" 16'-7" 18'-7" 20'-7"
38' 14'-10" 16'-10" 18'-10" 20’-10"
40' 15'-1" 17'-1" 19'-1" 21'-1"
42' 15'-4" 17'-4" 19'-4" 21'-4"
44' 15'-7" 17'-7" 19'-7" 21'-7"
46' 15'-10" 17'-10" 19'-10" 21'-10"
48' 16'-1" 18'-1" 20'-1" 22'-1"
50' 16'-4" 18'-4" 20'-4" 22'-4"
52' 16'-7" 18'-7" 20'-7" 22'-7"
Page view 34
1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 45 46

Comments to this Manuals

No comments